Available Variants:
- 700 X 700 mm - IS 9103
- 900 X 900 mm
- 1000 X 1000 mm
- Motorised - 76.2 cm Dia - M.S. Top - IS 1199
- Motorised - 76.2 cm Dia - Brass Top - IS 1199
- Hand Operated - 76.2 cm Dia - Brass Top - IS 1199
- Hand Operated - 76.2 cm Dia - M.S. Top - IS 1199
Variants Details:
1. 900 X 900 mm:
- As per IS:1199 (Part 6)-2018 / EN 12350-8.
- For slump-flow test for testing fresh concrete.
- Apparatus consists of a Slump Cone and an M.S. Base Plate.
- Base plate made from a flat steel plate, 3 mm thick.
- Plan area of at least 900 mm × 900 mm.
- Plate has a flat, smooth surface.
- Construction is stout enough to prevent distortion.
- Deviation from flatness is less than 3 mm at any point when a straight edge is placed between opposite sides and corners.
- Center of the plate is scribed with a cross, with lines parallel to the edges.
- Circles of 210 ± 1 mm diameter and 500 ± 1 mm diameter are provided with their centers coincident with the center point of the plate.
- All lines are maximum 2.0 mm wide and 1.0 mm deep.
- Essential accessories at extra cost:
- Mason Trowel – 6”
- Digital Stop Watch
- S.S. Scale – 1 mtr.
- G.I. Scoop – 8” x 4”
- Spirit Level – 1000 mm
- G.I. Container or Bucket – 10 Ltr. capacity
- Base plate can also be made of stainless steel at an extra cost.
2. 700 X 700 mm – IS 9103:
Compliance Standards:
- IS 9103
- EN 12350-5
- IS:1199-Part 2
Details:
- Flow table top constructed from a flat metal plate of minimum thickness 1.5 mm.
- Top has a plan area of 700 mm × 700 mm.
- Flatness within 1.5 mm.
- Center of the table scribed with a cross and central circle of 200 mm diameter.
- Under surface reinforced to prevent distortion.
- Front of flow table top provided with a lifting handle.
- Total mass of flow table top: 16 kg.
- Flow table top hinged to a base frame using externally mounted hinges.
- Front of base frame extends a minimum 120 mm beyond the flow table top.
- Upper stop provided on each side so that the lower front edge can only be lifted 40 ± 1 mm.
- Lower front edge provided with two hard rigid stops.
- Base frame constructed so that load is transferred directly to the surface on which the flow table is placed, with minimal tendency for the flow table top to bounce.
- Accessory apparatus includes metal mould and hardwood tamping bar.
- Mould:
- Minimum thickness 1.5 mm.
- Hollow frustum of a cone.
- Top diameter: 130 ± 2 mm.
- Base diameter: 200 ± 2 mm.
- Height: 200 ± 2 mm.
- Base and top open and parallel to each other and at right angles to the axis.
- Tamping bar made of hardwood.
- Tamping bar section: 40 mm × 40 mm.
- Tamping bar length: 200 mm with circular section handle.
- Essential accessories at extra cost:
- Masonary Trowel – 6”
- Digital Stop Watch
- S.S. Scale – 1 mtr.
3. 1000 X 1000 mm:
- Flow table apparatus constructed in accordance with Fig. 1A and 1B of IS 9103.
- Flow table top constructed from a flat metal plate of minimum thickness 1.5 mm.
- Top has a plan area of 1000 mm × 1000 mm.
- Flatness within 1.5 mm.
- Center of the table scribed with a cross and central circle of 200 mm diameter.
- Under surface reinforced to prevent distortion.
- Front of flow table top provided with a lifting handle.
- Flow table top hinged to a base frame using externally mounted hinges.
- Front of base frame extends a minimum 120 mm beyond the flow table top.
- Upper stop provided on each side so that the lower front edge can only be lifted 40 ± 1 mm.
- Lower front edge provided with two hard rigid stops.
- Base frame constructed to transfer the load directly to the surface on which the flow table is placed, with minimal tendency for the flow table top to bounce.
- Accessory apparatus includes a metal mould.
- Essential accessories at extra cost:
- Mason Trowel – 6”
- Digital Stop Watch
- S.S. Scale – 1 mtr.
- G.I. Scoop – 8” x 4”
- Spirit Level – 1000 mm
- G.I. Container or Bucket – 10 Ltr. capacity
4. Motorised - 76.2 cm Dia - M.S. Top:
- As per IS:1199-1959 (R.A.2004).
- M.S. table top, 762 mm diameter, finely machined at the top with reinforcing ribs at the bottom.
- Vertical shaft fitted to the underside of the table in the center.
- Cast iron frame with machined base and polished smooth vertical hole for the table shaft.
- Horizontal shaft carries a cam at one end and a hand wheel at the other with appropriate motor assembly for rotation.
- Conical mould in the form of frustum of a cone:
- 250 mm inside diameter at base.
- 170 mm inside diameter at top.
- 120 mm high.
- Mould provided with two lifting handles.
- Complete with one tamping rod, 0–60 cm long × 16 mm diameter.
- Ground and hardened steel cam designed to drop the table by 12.5 mm.
- Electrically operated to raise and drop the table top approximately 15 times in 15 seconds.
- Suitable for operation on 230 volts, 50 cycles, A.C. supply.
5. Motorised - 76.2 cm Dia - Brass Top:
- As per IS:1199 (1959) R.A.2004.
- Brass table top, 762 mm diameter, finely machined at the top with reinforcing ribs at the bottom.
- Vertical shaft fitted to the underside of the table in the center.
- Cast iron frame with machined base and polished smooth vertical hole for the table shaft.
- Horizontal shaft carries a cam at one end and a hand wheel at the other with appropriate motor assembly for rotation.
- Conical mould in the form of frustum of a cone:
- 250 mm inside diameter at base.
- 170 mm inside diameter at top.
- 120 mm high.
- Mould provided with two lifting handles.
- Complete with one tamping rod, 0–60 cm long × 16 mm diameter.
- Ground and hardened steel cam designed to drop the table by 12.5 mm.
- Electrically operated to raise and drop the table top approximately 15 times in 15 seconds.
- Suitable for operation on 230 volts, 50 cycles, A.C. supply.
6. Hand Operated - 76.2 cm Dia - Brass Top:
- As per IS:1199-1959 (R.A.2004).
- Flow table for determining the flow of Portland cement concrete.
- Flow table top 76.2 cm (30") diameter, finely machined from Brass/Gunmetal.
- Stand fabricated out of cast iron/mild steel and of sturdy construction.
- Ground and hardened steel cam designed to drop the table by 12.5 mm.
- Complete with flow mould with handles.
- Complete with one tamping rod, 60 cm long × 16 mm diameter.
7. Hand Operated - 76.2 cm Dia - M.S. Top:
- As per IS:1199-1959 (R.A.2004).
- Flow table for determining the flow of Portland cement concrete.
- Flow table top 76.2 cm (30") diameter, finely machined from Mild Steel.
- Stand fabricated out of cast iron/mild steel and of sturdy construction.
- Ground and hardened steel cam designed to drop the table by 12.5 mm.
- Complete with flow mould with handles.
- Complete with one tamping rod, 60 cm long × 16 mm diameter.
Common Essential Accessories:
Where specified in the source:
- Mason Trowel – 6”
- Digital Stop Watch
- S.S. Scale – 1 mtr.